![]() ![]() Switch the infrared lights to auto or off. Switch FTP upload of photo and video when motion is detected. Switch email alerts from the camera when motion is detected. When the camera supports AI objects detection, a binary sensor is created for each type of object (person, vehicle, pet) Switchĭepending on the camera, the following switches are created: Switch ParameterĬontrol how many seconds it takes (after the last motion detection) for the binary sensor to switch off. ![]() Please notice: for using the motion detection, your Homa Assistant should be reachable (within you local network) over http (not https). The time to switch motion detection off can be configured via the options menu, located at the integrations page. ![]() When the camera supports motion detection events, a binary sensor is created for real-time motion detection. When using a NVR, switch between the different camera streams. When using a single camera, choose stream 0. Switch between the RTMP or RTSP streaming protocol. Switch between h264 and h265 stream formats. Switch between Sub or Main camera stream. In the options menu, the following parameters can be configured: Parameter This integration creates a camera entity, providing a live-stream configurable from the integrations page. The camera keeps moving until the STOP command is passed to the service. Not applicable for the commands: STOP and AUTO. The possible presets are listed as attribute on the camera. In case of the command TOPOS, pass the preset ID here. Possibe values are: AUTO, DOWN, FOCUSDEC, FOCUSINC, LEFT, LEFTDOWN, LEFTUP, RIGHT, RIGHTDOWN, RIGHTUP, STOP, TOPOS, UP, ZOOMDEC and ZOOMINC. The day and night mode parameter supports the following values: AUTO Auto switch between black & white mode COLOR Always record videos in color mode BLACKANDWHITE Always record videos in black & white mode.Ĭontrol the PTZ (Pan Tilt Zoom) movement of the camera. Set the day and night mode parameter of the camera. The backlight parameter supports the following values: BACKLIGHTCONTROL: use Backlight Control DYNAMICRANGECONTROL: use Dynamic Range Control OFF: no optimization This may improve image clarity in high contrast situations, but it should be tested at different times of the day and night to ensure there is no negative effect. Optimizing brightness and contrast levels to compensate for differences between dark and bright objects using either BLC or WDR mode. Presets can be found in the Web UI of the camera. The sensitivity to set, a value between 1 (low sensitivity) and 50 (high sensitivity). Either all time schedule presets can be set at once, or a specific preset can be specified. Set the motion detection sensitivity of the camera. The Reolink integration supports all default camera services and additionally provides the following services: Service reolink_dev.set_sensitivity Be aware that this can be reset during a firmware upgrade. It might be disabled by default and can only be enabled when you have a screen connected to the NVR, not via webb or app clients. Make sure ONVIF is enabled on your camera/NVR.Make sure you have set up the Internal URL in Home Assistant to the correct IP address and port (do not use the mDNS name).Users are created and managed through the web interface of the camera (Device Settings / Cog icon -> User) or through the app (Device Settings / Cog icon -> Advanced -> User Management). Users of type "Guest" can only view the switch states but cannot change them and cannot call the services. So when using https internally, motion detection will not work at this moment.įor the services and switch entities of this integration to work, you need a camera user of type "Administrator". The camera and other sensors will now be available as an entity.įor the motion detection to work, Home Assistant must be reachable via http from your local network. In your Home Assistant installation go to: Configuration > Integrations, click the button Add Integration > Reolink IP cameraĮnter the details for your camera. Also clear your browser cache before proceeding to the next step, as the integration may not be visible otherwise. ⚠️ After executing one of the above installation methods, restart Home Assistant. Click Install on the Reolink IP camera box that has now appeared.Paste the repository URL ( ) in the dialog box. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |